Atlantic Society of Radio Controlled Modellers | |
https://www.asrcm.ns.ca/cgi-bin/yabb2/YaBB.pl
Atlantic Society of Radio Control Modellers >> General Discussions >> my new plane arrived today https://www.asrcm.ns.ca/cgi-bin/yabb2/YaBB.pl?num=1334016260 Message started by astroflyer on Apr 9th, 2012 at 9:04pm |
Title: my new plane arrived today Post by astroflyer on Apr 9th, 2012 at 9:04pm
Geoff says it's a high wing geebee.
Joan says it's ugly! I love it! massive fuse, short wings, high wing loading.....should be fun! ;D stuck together for a peek, no graphics yet, although there are not many on this famous airplane. ![]() ![]() |
Title: Re: my new plane arrived today Post by JON BOY on Apr 9th, 2012 at 10:02pm
Thats awesome! I love that plane and all from that era of avaition. Thats one that I could easily own. The Gee Bee and this plane should have a flight together sometime!
|
Title: Re: my new plane arrived today Post by astroflyer on Apr 9th, 2012 at 10:20pm
think your geebee could stay with me? ;D ;D
|
Title: Re: my new plane arrived today Post by JON BOY on Apr 10th, 2012 at 4:51am
Yer toast! ;D ;D
|
Title: Re: my new plane arrived today Post by SandyM on Apr 10th, 2012 at 9:22am
looks something like a Mulligan ??
|
Title: Re: my new plane arrived today Post by astroflyer on Apr 10th, 2012 at 3:02pm
yessir , sure is. kit from great planes has every screw , clevis and fitting. needs nothing except motor and electrics. very well engineered .
http://www.youtube.com/watch?v=Bk_ORzMI1r4 |
Title: Re: my new plane arrived today Post by Ben Lann on Apr 11th, 2012 at 5:38pm
Looks very capable in the video and it's electric powered! SWEEET! :o
|
Title: Re: my new plane arrived today Post by astroflyer on Apr 11th, 2012 at 5:49pm Ben Lann wrote on Apr 11th, 2012 at 5:38pm:
yes, no slime for me ever again. ;D got the flap and aileron servos in it last night. probably gonna setup the elevator and rudder tonight. then it's just the motor setup and detail the dummy engine. |
Title: Re: my new plane arrived today Post by astroflyer on May 7th, 2012 at 9:27pm
attention joe and craig!
just need to run the wiring and decals. ;D ![]() ![]() ![]() |
Title: Re: my new plane arrived today Post by JMiller on May 7th, 2012 at 9:30pm
Hey, that's looking great. We may see it fly some time this season after all! ;D ;D
|
Title: Re: my new plane arrived today Post by astroflyer on May 7th, 2012 at 9:39pm
I dunno. after drilling multible holes and glueing all those fake pushrods in, almost every one out of alignment, I need another break! ;D
|
Title: Re: my new plane arrived today Post by astroflyer on May 11th, 2012 at 4:26pm
Ready for the first flight.
I will be removing the wheel pants for the grass field for obvious reasons. I did not add the wing struts because: 1. non functional 2. poor fit 3. very heavy. made of metal and somewhere in the area of six ounces. very strong but too heavy! ![]() ![]() ![]() ![]() |
Title: Re: my new plane arrived today Post by astroflyer on May 11th, 2012 at 10:14pm
I flew two test flights friday night in some wind. It flew as expected after a few clicks of up trim and a touch of right.
Both landings were a bit hot and resulted in nose over both times, much like jon's geebee. I should have not read the internet crap about the high wing loading. ;D It will land a lot slower as I get used to it. The pitch up with flaps is strong, but a flap/elevator mix I set up took care of that nicely. overall I'm pretty pleased with it. ;D |
Title: Re: my new plane arrived today Post by shawn m on May 11th, 2012 at 11:52pm
Keep in mind that stickers ad weight although they look cool Al... You should just go for the gusto and put on the struts for full effect. I can't wait to see it up in the air..
Shawn M |
Atlantic Society of Radio Controlled Modellers » Powered by YaBB 2.5.2! YaBB Forum Software © 2000-2024. All Rights Reserved. |